|
ANODIZING SUPPLIES
ANODIZING DYES
Above
are some of our available colors that were anodized with the
very same chemical steps in our 'Show
Anodizing Kit' and our Bright Dip. All samples are
done on 4000 series aluminum cable
brackets
that we had bought at a local hardware store with a matte
finish. No buffing or polishing was done on these
parts. Results on 6000 series will be
as good or
better than this. Compare this finish to any
other illustrated on the internet or
catalog
and you will see there is no comparison.
DIGITAL PH METER FOR
TESTING ANODIZING DYES AND ANODIZING SEALERS - $50 with
calibration solution packs
ALL
DYES ARE RATED 6 OR HIGHER FOR LIGHT-FASTNESS.
Orange $12.00
Red $7.00
Blue $7.00
Green $9.00 24K GOLD $24.00
14K GOLD $22.00
Purple $9.00 Vibe
Red $16.00
Vibe Green
$16.00
Black $24.00
Vibe
Blue $16.00 Violet $16.00
Dark Brown $16 Light Brown
$12 Bronze $16
Color chart for more dyes are below
Each container can make up to 2 gallons of dye.
OTHER ANODIZING AND
CHEM FILM SUPPLIES
BRIGHT DIP: The picture on
the left was matte finish part prior to Bright Dip. To
the right is the same part after Bright Dip for
two minutes. The Bright Dip
is $61.00 per
gallon when purchased with a kit and $69.00
per gallon when purchased separately. Used to
brighten a polished part prior to anodizing. The part
will shine so bright you will not believe your eyes. A
must for true show anodizing. No need to buff.
Just dip and anodize. Hazmat.
Teflon Sealer:
(makes the amount shown) $60
/ makes a gallon - $99/
two gallons - $169/
makes four gallons
- $189/ five gallons
- $279 for eight gallon.
This sealer is used for placing a
teflon coating onto anodized
aluminum which will place a super slick, heat resistant
coating onto the final product.
Paintball gun barrels are one of the most common application
of teflon sealing. Great for all types of anodizing
whether it's show, hard coat, salt resistant, or super thick
anodizing.
ANODIZE-STRIP:
will strip old or unwanted anodizing in a
matter of a few seconds to a few
minutes. You will not find a faster stripper. Contains
inhibitors to slow the attack on base metal, once the
anodizing film has been stripped. Two gallon is $30.00
and four gallons is $50.00.
Aluma Soak:
$20.00 /
two gallons
make-up. A true aluminum soak formulated for anodizing
and plating aluminum. Not an all-purpose cleaner.
Use only with aluminum or pot metal.
Etch PS: $20.00
/
two gallons
makeup...Used to etch aluminum
prior to anodizing or plating
Desmut-AL 2:
(can ONLY be sold to registered businesses) $45
/
two gallon makeup.
De-oxidizes, removes smut,
and much, much more. Hazmat
Desmut-AL
1:
Home version of Desmut. Works the same but just
takes a little longer $30 /
two gal make-up. De-oxidizes,
removes smut, and much.
Kool Seal:
$24 / gallon make
up Used for sealing aluminum after anodizing and
dyeing. Seals anodize aluminum
without the pain of using steam or boiling some hot nickel
sealer. Used at room temperature. Just dip
and seal. No need to sit and wait over 60 minutes for steam
sealing. This sealer is much easier to use than a hot nickel
acetate sealer and leaves no 'smut' as is common in hot
nickel seals. Plus you do NOT have to heat it to
almost boiling like hot nickel seals. We are not aware
of any easier way to seal anodizing.
Mid Temp
Seal: $19 / two gallons make up Sealing
anodized aluminum after dyeing.
Seals anodize aluminum by heating seal to
near boiling. Additive
in Hot Seal eliminates any smutting problem common in most
heated seals.
  
 
MASKING
PRODUCTS:
OUR MOST
POPULAR MASKING PRODUCT - Rubberized
Masker:
Small Can
$30.00
or Large for $100.00.
This is a special temperature and corrosive resistant
coating that can be used to mask off certain areas for
either multi-color anodizing or for omitting certain areas
from being exposed to the anodizing process. Paint it
on, dries in minutes, and when you are finish, just peel it
off. One pound covers almost 500 square inches.
This item is a 'must-have' for anyone looking to do splash
anodizing or silk-screen anodizing.
Plating/Anodizing Adhesive Making Tape:
$22 a roll
(3/4" wide) This corrosive and temperature
resistant tape should be used only to mask off areas that
will not be exposed to the plating or anodizing process
throughout the entire process.
Large 4" Wide Roll of Plating/Anodizing Adhesive Making Tape:
$49 a roll
(1"X 25 yards) This corrosive and temperature
resistant tape should be used only to mask off areas that
will not be exposed to the plating or anodizing process
throughout the entire process.
Titanium
Racking Wire: ONCE YOU GO
TITANIUM, YOU NEVER GO BACK.
For trouble free racking on aluminum parts. These
wires and rods will not lose conductivity when anodized (as
is the case with aluminum wire). Can be used over and
over again without be stripped. Just rinse and
re-rack. Will last and last.
Cost $1.00 per foot.
Titanium Chiller
U-Coil:
($60 and up) This is
used for making an inexpensive heat exchanger for cooling of
any anodizing. Build your own chiller set-up for less
than $80.00 with parts found at
many hardware or aquarium retailers.
LINKS:
Home
More
Chrome Plating Studio
Commercial Plating Lines
Electropolishing Studio and Lines
Anodizing Studio
Other non chrome plating
Plating of plastic and other non metals
Electroless Plating
Used
Plating Equipment
Larger Studio Hobby Anodizing
and Plating Kits
Example of
Industrial Commercial Plating or Anodizing Lines
Buffing and Polishing Equipment and
Machines
More Industrial Plating and Anodizing
Lines
|
